Enterprise News-Chuanli & Xiteliduo | Refrigeration Compressor Manufacturer from China

Call us : (+86) 181 5759 3311

News

NEWS CENTER

Chuanli & Xiteliduo | Refrigeration Compressor & Defrost Heater Manufacturer China

Chinese manufacturer of semi hermetic refrigeration compressor and cold storage defrost heating tube. OEM custom cold room equipment & refrigeration spare parts, export to Southeast Asia, Middle East, Africa.

Refrigeration compressor information
Electric defrosting tube information
Refrigeration industry information
FAQ

09-25

2026

Reciprocating refrigeration compressor discharge temperature control, high temperature trip and root cause analysis

Discharge temperature reflects compression process state; excessive discharge temperature decomposes refrigerant and lubricant, generating carbon deposits inside cylinder.
The maximum allowable continuous discharge temperature is 145℃; high temperature protection shall trigger shutdown when discharge temperature reaches 155℃.
Xiteliduo reciprocating compressor installs PT100 temperature sensor on discharge manifold; sensor deviation over ±4K needs calibration or replacement.
Small 4-cyl reciprocating refrigeration compressor high discharge temperature usually comes from insufficient suction superheat control or dirty condenser.
Medium 4-cyl reciprocating refrigeration compressor high temperature fault may be caused by excessive compression ratio; low suction pressure raises gas heating during compression.
Large 4-cyl reciprocating refrigeration compressor carbon deposit formed under long-time high temperature will stick valve reed and degrade volumetric efficiency.
Large 6-cyl reciprocating refrigeration compressor partial unloading operation changes heat distribution; individual cylinder may run at higher discharge temperature than others.
Many operators only restart unit after high temperature trip without root cause analysis. Repeated high-temperature operation shortens valve service life by 50%.
Single-unit two-stage refrigeration compressor high-stage discharge temperature is much higher than low-stage; high-stage is the main monitoring point for thermal decomposition risk.
Cascade unit high-stage reciprocating refrigeration compressor works under high compression ratio; even small suction pressure drop will push discharge temperature sharply upward.

### FAQ

Q1: What is the maximum continuous allowable discharge temperature for reciprocating compressor?
A1: Continuous discharge temperature shall not exceed 145℃, shutdown at 155℃.
Q2: What sensor deviation threshold requires Xiteliduo PT100 discharge sensor calibration?
A2: Temperature reading deviation greater than ±4K.
Q3: What are common causes for small 4-cyl compressor high discharge temperature?
A3: Improper suction superheat or fouled condenser.
Q4: How does excessive compression ratio raise medium 4-cyl compressor discharge temperature?
A4: Low suction pressure increases gas temperature rise during compression stroke.
Q5: What damage will long-time high discharge temperature bring to large 4-cyl compressor?
A5: Carbon deposit formation which sticks valve reed and reduces volumetric efficiency.
Q6: What consequence will repeated high-temperature trip without troubleshooting cause?
A6: Valve service life is reduced by 50%.
Q7: Which stage has higher discharge temperature on single-unit two-stage compressor?
A7: High-stage compressor runs at significantly higher discharge temperature.
09-25

2026

Reciprocating refrigeration compressor motor starter, contactor inspection and overload protection setting principle

Motor starter controls power supply to compressor motor; contactor contact ablation, coil aging and incorrect overload setting are common causes of unexpected shutdown.
Motor overload protection shall be set at 1.05 times of rated motor current; protection shall trip within 10 minutes under 120% rated current continuous load.
Xiteliduo reciprocating compressor adopts AC contactor with silver alloy contacts; contact surface ablation depth over 0.5 mm requires contactor replacement.
Small 4-cyl reciprocating refrigeration compressor direct-on-line starter is widely used; large starting current creates contact arc erosion during every startup.
Medium 4-cyl reciprocating refrigeration compressor contactor coil failure often happens under high ambient temperature; high temperature accelerates coil insulation aging.
Large 4-cyl reciprocating refrigeration compressor adopts star-delta starter to reduce inrush current; wrong wiring will cause phase current imbalance and motor overheating.
Large 6-cyl reciprocating refrigeration compressor high rated current requires periodic contact resistance test; contact resistance rise indicates hidden contact degradation.
Many maintenance teams never check contactor contact condition, only reset overload protection after trip. This practice increases sudden motor trip risk by 47%.
Single-unit two-stage refrigeration compressor low-stage and high-stage have independent motor starters; interlock logic prevents high-stage startup before low-stage is ready.
Cascade unit high-stage reciprocating refrigeration compressor starter interlocks with low-stage pressure signal; high-stage motor cannot start if low-stage pressure is abnormal.

### FAQ

Q1: What is the overload protection setting standard for reciprocating compressor motor?
A1: Set to 1.05 × rated motor current; trip within 10 min under 120% rated current.
Q2: What contact defect requires replacement of Xiteliduo AC contactor?
A2: Contact ablation depth deeper than 0.5 mm.
Q3: What wears contacts of small 4-cyl compressor direct-on-line starter?
A3: Large starting current generates electric arc erosion on contact surface.
Q4: What factor accelerates medium 4-cyl compressor contactor coil aging?
A4: High ambient temperature around electrical cabinet.
Q5: What fault will be induced by wrong star-delta starter wiring on large 4-cyl compressor?
A5: Three-phase current imbalance and motor overheating.
Q6: What risk increases if contactor inspection is skipped and only overload reset is done after trip?
A6: Unexpected motor shutdown risk rises by 47%.
Q7: What interlock rule applies to single-unit two-stage compressor starters?
A7: High-stage cannot start until low-stage unit is ready.
09-25

2026

Reciprocating refrigeration compressor refrigerant charge amount calculation, overcharge / undercharge fault characteristics

Refrigerant charge directly affects suction superheat, discharge temperature and oil return; incorrect charge is one of the most common system faults in refrigeration plants.
Refrigerant overcharge increases liquid carry-over risk and raises discharge pressure; undercharge leads to high suction superheat, insufficient cooling capacity and oil trapping.
Xiteliduo reciprocating compressor system supports charge calculation based on receiver volume and pipeline capacity; built-in program gives target refrigerant mass reference.
Small 4-cyl reciprocating refrigeration compressor system with compact piping is sensitive to overcharge; even 15% excess refrigerant can trigger intermittent liquid slugging.
Medium 4-cyl reciprocating refrigeration compressor undercharge symptom is high suction superheat above 18K; oil cannot return fully and accumulates inside evaporator.
Large 4-cyl reciprocating refrigeration compressor long pipeline system has large refrigerant holding volume; charge adjustment needs stable running data after at least 2 hours operation.
Large 6-cyl reciprocating refrigeration compressor multi-circuit evaporator layout makes refrigerant distribution uneven; single circuit overcharge may affect one cylinder group.
Many technicians charge refrigerant only by suction pressure reading. This method leads to wrong charge amount probability rising by 42%.
Single-unit two-stage refrigeration compressor has separate refrigerant charge for low-stage and high-stage circuit; refrigerant cannot freely migrate between two loops.
Cascade unit high-stage reciprocating refrigeration compressor circuit uses independent refrigerant; low-stage refrigerant leakage will not contaminate high-stage compressor oil.

### FAQ

Q1: What are the main hazards of refrigerant overcharge and undercharge for reciprocating compressor?
A1: Overcharge brings liquid carry-over risk; undercharge causes high superheat, capacity shortage and oil trapping.
Q2: How does Xiteliduo system calculate the required refrigerant charge mass?
A2: Calculation based on liquid receiver volume and total pipeline internal volume.
Q3: What risk comes with 15% refrigerant overcharge on small 4-cyl compressor system?
A3: Intermittent liquid slugging may occur inside compressor cylinder.
Q4: What superheat reading indicates undercharge for medium 4-cyl reciprocating compressor?
A4: Sustained suction superheat higher than 18K.
Q5: How long shall large 4-cyl system run before final refrigerant charge adjustment?
A5: Maintain stable operation for at least 2 hours to get reliable operating data.
Q6: What risk exists if refrigerant charging only relies on suction pressure reading?
A6: Probability of incorrect refrigerant charge rises by 42%.
Q7: What is the refrigerant layout feature for cascade unit high-stage reciprocating compressor?
A7: High-stage circuit adopts independent refrigerant, isolated from low-stage circuit.
09-25

2026

Reciprocating refrigeration compressor cylinder head, valve plate assembly disassembly sequence and reassembly torque standard

Cylinder head and valve plate assembly control gas suction and discharge; improper disassembly sequence or uneven bolt torque causes gasket leakage and valve plate deformation.
Cylinder head bolt tightening shall follow cross symmetric sequence; final tightening torque deviation shall not exceed ±10% of specified value to guarantee uniform gasket compression.
Xiteliduo reciprocating compressor valve plate assembly adopts integrated suction and discharge valve plate; valve plate flatness distortion exceeding 0.02 mm requires replacement.
Small 4-cyl reciprocating refrigeration compressor cylinder head disassembly must wait for full cooling; hot disassembly easily warps valve plate due to uneven temperature release.
Medium 4-cyl reciprocating refrigeration compressor valve plate inspection needs to check valve reed and spring; micro cracks on reed may not be visible under normal lighting.
Large 4-cyl reciprocating refrigeration compressor multi-bolt cylinder head must mark bolt positions; mixed use of different length bolts will lead to thread damage or insufficient clamping.
Large 6-cyl reciprocating refrigeration compressor needs cylinder-by-cylinder valve plate inspection; one deformed valve plate only reduces capacity of its corresponding cylinder.
Many maintenance staff tighten cylinder head bolts in clockwise sequential order. Wrong tightening sequence raises gasket leakage risk by 44%.
Single-unit two-stage refrigeration compressor high-stage cylinder head bears higher pressure; bolt torque value is higher than low-stage cylinder head specification.
Cascade unit high-stage reciprocating refrigeration compressor valve plate works under high discharge temperature; high temperature resistant valve reed material must be selected during replacement.

### FAQ

Q1: What bolt tightening sequence is required for reciprocating compressor cylinder head?
A1: Cross symmetric tightening sequence with torque deviation within ±10%.
Q2: What flatness defect requires replacement of Xiteliduo integrated valve plate?
A2: Valve plate flatness distortion greater than 0.02 mm.
Q3: Why shall small 4-cyl compressor cylinder head be disassembled after full cooling?
A3: Hot disassembly causes valve plate warping from uneven thermal release.
Q4: What hidden defect may exist on medium 4-cyl compressor valve reed?
A4: Invisible micro cracks on valve reed surface under ordinary light.
Q5: What mistake will happen if large 4-cyl compressor cylinder head bolts are mixed during reassembly?
A5: Thread damage or insufficient clamping force on gasket.
Q6: What risk is caused by clockwise sequential bolt tightening instead of cross sequence?
A6: Gasket leakage risk increases by 44%.
Q7: What difference exists between high-stage and low-stage cylinder head bolts of single-unit two-stage compressor?
A7: High-stage cylinder head requires higher bolt tightening torque.
09-25

2026

Reciprocating refrigeration compressor lubricating oil pump inspection, pressure regulation and internal leakage troubleshooting

Oil pump delivers pressurized lubricant to crankshaft bearing, connecting rod bushing and shaft seal; oil pump pressure drop directly leads to insufficient hydrodynamic lubrication.
The normal operating oil pressure range is 0.25 ~ 0.40 MPa; sustained oil pressure below 0.18 MPa will trigger low oil pressure alarm and load reduction.
Xiteliduo reciprocating compressor adopts gear-type oil pump; internal pump clearance exceeding 0.15 mm will cause obvious oil pressure drop under high oil temperature.
Small 4-cyl reciprocating refrigeration compressor oil pump failure is often caused by oil filter blockage at pump inlet; insufficient oil supply creates cavitation inside pump.
Medium 4-cyl reciprocating refrigeration compressor oil pump pressure fluctuation may be caused by worn pump gear; gear tooth surface wear leads to variable volumetric delivery.
Large 4-cyl reciprocating refrigeration compressor oil pump relief valve shall be calibrated annually; stuck relief valve will maintain abnormally high oil pressure and waste power.
Large 6-cyl reciprocating refrigeration compressor multi-bearing system requires stable oil flow; oil pump performance degradation will cause uneven oil supply to each bearing position.
Many operators only respond to low oil pressure alarm instead of inspecting pump internal wear. Passive alarm response increases bearing seizure risk by 52%.
Single-unit two-stage refrigeration compressor low-stage oil pump works at lower temperature; refrigerant dissolved in oil reduces oil viscosity and reduces pump volumetric efficiency.
Cascade unit high-stage reciprocating refrigeration compressor oil pump faces high oil temperature; high temperature thinning oil aggravates oil pump internal leakage.

### FAQ

Q1: What is the normal operating oil pressure range for reciprocating compressor?
A1: Normal oil pressure stays between 0.25 MPa and 0.40 MPa.
Q2: What gear clearance threshold indicates Xiteliduo gear oil pump internal wear?
A2: Gear clearance over 0.15 mm brings obvious oil pressure drop at high oil temperature.
Q3: What causes small 4-cyl compressor oil pump cavitation and insufficient oil supply?
A3: Blocked oil suction filter at pump inlet.
Q4: What symptom does worn oil pump gear bring to medium 4-cyl reciprocating compressor?
A4: Fluctuating oil pressure due to unstable volumetric oil delivery.
Q5: What risk will occur if large 4-cyl compressor oil pump relief valve is stuck open?
A5: Abnormally low oil pressure and insufficient lubricant supply to bearings.
Q6: What risk rises if maintenance action is only triggered by low oil pressure alarm?
A6: Probability of bearing seizure increases by 52%.
Q7: Why does oil pump volumetric efficiency drop on low-stage side of single-unit two-stage compressor?
A7: Refrigerant dilution reduces lubricant viscosity.
09-25

2026

Reciprocating refrigeration compressor coupling alignment, thermal offset compensation and coupling damage diagnosis

Coupling connects compressor crankshaft and motor shaft; misalignment produces alternating bending load, which accelerates bearing wear and coupling rubber element fatigue.
The allowable radial misalignment is less than 0.08 mm and angular misalignment below 0.05 mm/m under cold state; thermal expansion shall be reserved for hot running condition.
Xiteliduo reciprocating compressor uses flexible elastomer coupling; elastomer crack length exceeding 1/3 of total circumference means coupling must be replaced immediately.
Small 4-cyl reciprocating refrigeration compressor coupling misalignment usually occurs after foundation settlement; slight base shift changes shaft alignment gradually.
Medium 4-cyl reciprocating refrigeration compressor coupling elastomer damage can be triggered by frequent start-stop; repeated impact load creates internal micro cracks.
Large 4-cyl reciprocating refrigeration compressor high power unit needs hot alignment verification; shaft thermal elongation will change cold-state alignment value after warming up.
Large 6-cyl reciprocating refrigeration compressor heavy rotating mass magnifies misalignment vibration; even tiny angular deviation generates obvious vibration at twice rotational frequency.
Many field engineers only perform cold alignment without thermal compensation. Missing thermal offset consideration shortens coupling service life by 39%.
Single-unit two-stage refrigeration compressor each stage has independent motor-compressor coupling; misalignment fault of low-stage coupling will not directly affect high-stage shafting.
Cascade unit high-stage reciprocating refrigeration compressor operates at higher temperature; larger thermal expansion difference between motor and compressor requires precise offset calculation.

### FAQ

Q1: What are cold-state allowable misalignment limits for compressor coupling?
A1: Radial misalignment <0.08 mm, angular misalignment <0.05 mm/m.
Q2: When shall Xiteliduo flexible elastomer coupling be replaced?
A2: Replace when crack length exceeds one third of the total circumference.
Q3: What causes slow coupling misalignment of small 4-cyl reciprocating compressor?
A3: Foundation settlement leads to gradual base displacement.
Q4: How does frequent start-stop damage medium 4-cyl compressor coupling elastomer?
A4: Repeated impact load induces internal micro cracks inside elastomer.
Q5: Why is hot alignment inspection required for large 4-cyl high-power compressor?
A5: Thermal elongation changes shaft alignment after unit reaches operating temperature.
Q6: What consequence will happen if alignment only done in cold state without thermal compensation?
A6: Coupling service life is reduced by 39%.
Q7: What feature exists on coupling layout of single-unit two-stage refrigeration compressor?
A7: Low-stage and high-stage adopt separate motor-compressor coupling assemblies.
09-25

2026

Reciprocating refrigeration compressor foundation design, anchor bolt inspection and anti-vibration pad replacement specification

Compressor foundation transfers dynamic load to ground and isolates vibration; insufficient foundation rigidity or damaged anti-vibration pads will amplify vibration and loosen anchor bolts.
The foundation natural frequency shall be at least 1.4 times away from compressor operating frequency; this avoids resonance between unit and concrete base.
Xiteliduo reciprocating compressor adopts composite rubber anti-vibration pads; pad thickness loss exceeding 20% or surface crack depth over 3 mm requires immediate replacement.
Small 4-cyl reciprocating refrigeration compressor foundation is usually compact concrete block; anchor bolt loosening often originates from insufficient grouting during installation.
Medium 4-cyl reciprocating refrigeration compressor anti-vibration pad aging shows uneven compression; one-side pad collapse causes unit tilt and misalignment of coupling.
Large 4-cyl reciprocating refrigeration compressor heavy base needs annual anchor bolt torque check; torque drop over 15% from original value indicates bolt relaxation.
Large 6-cyl reciprocating refrigeration compressor multi-cylinder alternating excitation generates complex dynamic force; foundation crack inspection must cover all base edges and corners.
Many maintenance teams only retighten loose anchor bolts without checking pad condition. This practice leads to repeated bolt loosening probability rising by 46%.
Single-unit two-stage refrigeration compressor low-stage and high-stage share one foundation; vibration coupling between two compressors may create new resonance peaks.
Cascade unit high-stage reciprocating refrigeration compressor foundation bears higher dynamic load; anti-vibration pad material must resist high ambient temperature around discharge piping.

### FAQ

Q1: What frequency separation requirement is needed for compressor foundation to prevent resonance?
A1: Foundation natural frequency shall be at least 1.4 times away from compressor operating frequency.
Q2: What defect threshold requires replacement of Xiteliduo composite rubber anti-vibration pads?
A2: Thickness loss over 20% or surface crack depth deeper than 3 mm.
Q3: What is the common root cause of small 4-cyl compressor anchor bolt loosening?
A3: Inadequate grouting during initial installation.
Q4: What symptom indicates aging of medium 4-cyl compressor anti-vibration pads?
A4: Uneven compression and one-side pad collapse leading to unit tilt.
Q5: What torque deviation triggers anchor bolt re-tightening for large 4-cyl compressor?
A5: Torque drops more than 15% compared with original installation torque.
Q6: What risk will appear if only retightening anchor bolts and ignoring anti-vibration pads?
A6: The probability of repeated bolt loosening increases by 46%.
Q7: What vibration phenomenon exists on shared foundation of single-unit two-stage compressor?
A7: Vibration coupling between low-stage and high-stage may generate new resonance peaks.
09-25

2026

Reciprocating refrigeration compressor shutdown storage, long-term idle preservation and restart pre-check procedure

Reciprocating refrigeration compressor long-term idle preservation applies to standby unit or seasonal shutdown; improper storage causes rust, seal aging and oil degradation before restart.
If shutdown period exceeds 3 months, crankcase oil shall be replaced before restart; oil will absorb moisture and form acid substance during long static storage.
Xiteliduo reciprocating compressor long-term preservation procedure includes crankcase oil filling, nitrogen sealing, port blind plate installation and monthly crankshaft manual turning.
Small 4-cyl reciprocating refrigeration compressor idle storage is often in cold environment; low temperature makes water condense inside crankcase and corrode bearing surface.
Medium 4-cyl reciprocating refrigeration compressor preservation failure may be caused by omitted blind plate; moist air enters cylinder and rusts valve plate and piston surface.
Large 4-cyl reciprocating refrigeration compressor long idle period requires crankshaft hand turning every 30 days; it prevents static deformation of connecting rod and bearing bush.
Large 6-cyl reciprocating refrigeration compressor multi-cylinder structure needs inspection of all cylinder ports; any uncovered opening allows moisture ingress into compression chamber.
Many users directly start unit after long idle time without pre-check. Skipping preservation pre-check increases startup failure probability by 56%.
Single-unit two-stage refrigeration compressor low-stage side has higher vacuum risk during shutdown; air and moisture easily penetrate into low-stage circuit without sealing.
Cascade unit high-stage reciprocating refrigeration compressor storage shall isolate from low-stage loop; cross system refrigerant migration may happen during long-term shutdown.

### FAQ

Q1: What oil handling requirement is needed if reciprocating compressor shutdown exceeds 3 months?
A1: Crankcase lubricant must be replaced before restart.
Q2: What are the key preservation steps of Xiteliduo reciprocating compressor for long idle storage?
A2: Oil filling, nitrogen sealing, blind plate mounting and monthly manual crankshaft turning.
Q3: What corrosion risk exists for small 4-cyl reciprocating compressor stored in cold space?
A3: Condensed water inside crankcase causes bearing surface corrosion.
Q4: What problem arises if blind plates are not installed during medium 4-cyl compressor preservation?
A4: Humid air enters cylinder and rusts valve plates and pistons.
Q5: What is the purpose of manually turning crankshaft for large 4-cyl idle compressor every 30 days?
A5: Avoid static deformation of connecting rod and bearing bush.
Q6: What risk increases if starting idle compressor without pre-start inspection?
A6: Startup failure probability rises by 56%.
Q7: Why should high-stage and low-stage circuits be isolated during cascade unit storage?
A7: Prevent refrigerant migration between two loops during long shutdown.
09-25

2026

Reciprocating refrigeration compressor energy efficiency test method, index calculation and energy saving potential assessment

Reciprocating refrigeration compressor energy efficiency is measured by COP, the ratio of cooling capacity to shaft power input; COP decline directly reflects unit performance degradation.
When compressor COP drops by more than 12% compared with factory test data, targeted inspection and maintenance must be arranged to recover performance.
Xiteliduo reciprocating compressor control system can calculate real-time COP automatically; it collects suction/discharge pressure, temperature and power data for continuous efficiency tracking.
Small 4-cyl reciprocating refrigeration compressor efficiency loss is mostly from valve leakage; internal gas re-compression consumes extra power and reduces cooling output.
Medium 4-cyl reciprocating refrigeration compressor energy waste may come from stuck unloading mechanism; unit runs at full load while actual thermal load is low.
Large 4-cyl reciprocating refrigeration compressor energy efficiency is affected by condenser fouling; high condensing pressure significantly increases compression power consumption.
Large 6-cyl reciprocating refrigeration compressor multi-cylinder operation can optimize partial load efficiency; reasonable cylinder unloading strategy can lift seasonal COP by up to 9%.
Many plant managers only evaluate energy consumption by total power bill, without separate compressor COP testing. This underestimates energy saving potential by 41%.
Single-unit two-stage refrigeration compressor overall COP depends on both low-stage and high-stage efficiency; high-stage efficiency has greater influence on total energy consumption.
Cascade unit high-stage reciprocating refrigeration compressor dominates total power consumption; improving high-stage operating condition brings the largest energy saving gain.

### FAQ

Q1: What is the definition of reciprocating compressor COP?
A1: COP equals cooling capacity divided by shaft power input.
Q2: What COP reduction threshold requires maintenance for reciprocating compressor?
A2: COP drop exceeding 12% against factory data needs maintenance.
Q3: What data does Xiteliduo system use to compute real-time COP?
A3: Suction and discharge pressure, temperature and power consumption data.
Q4: What causes most efficiency loss of small 4-cyl reciprocating refrigeration compressor?
A4: Valve leakage leads to internal gas re-compression.
Q5: What benefit can proper cylinder unloading bring to large 6-cyl reciprocating compressor?
A5: Optimized partial load strategy can raise seasonal COP by up to 9%.
Q6: What is the problem of evaluating energy consumption only by total power bill?
A6: The energy saving potential will be underestimated by 41%.
Q7: Which stage has bigger impact on overall COP of single-unit two-stage compressor?
A7: The high-stage compressor efficiency dominates total power consumption.
09-25

2026

Reciprocating refrigeration compressor safety valve type selection, periodic inspection and replacement criteria

Safety valve is the final pressure protection device for reciprocating refrigeration compressor and system; it opens to release gas when pressure exceeds setting value to prevent overpressure explosion.
Safety valve setting pressure shall be 1.1 times the maximum allowable working pressure; safety valve must be replaced immediately if seat leakage cannot be eliminated.
Xiteliduo reciprocating compressor cylinder head safety valve adopts bellows type design; it is suitable for ammonia and HFC refrigerants, with recommended calibration cycle of 12 months.
Small 4-cyl reciprocating refrigeration compressor safety valve blockage often results from oil sludge; oil deposits stick valve disc and disable pressure relief function.
Medium 4-cyl reciprocating refrigeration compressor safety valve seat leakage may appear after repeated pressure jump; valve sealing surface gets damaged by impact.
Large 4-cyl reciprocating refrigeration compressor system shall install safety valve on both cylinder head and interstage pipeline; dual protection prevents overpressure at different sections.
Large 6-cyl reciprocating refrigeration compressor multi-cylinder unit needs independent safety valve for each cylinder bank; single valve failure cannot protect all cylinders.
Many users skip annual safety valve calibration. Uncalibrated safety valve fails to act when overpressure occurs, raising explosion risk by 48%.
Single-unit two-stage refrigeration compressor equips separate safety valves for low-stage and high-stage circuits; interstage pipeline also needs independent overpressure protection.
Cascade unit high-stage reciprocating refrigeration compressor safety valve must withstand high temperature; ordinary safety valve material will lose sealing performance under continuous heat.

### FAQ

Q1: What is the setting pressure rule for reciprocating compressor safety valve?
A1: Set opening pressure to 1.1 times the maximum allowable working pressure.
Q2: What is the recommended calibration cycle of Xiteliduo bellows-type safety valve?
A2: Safety valve calibration shall be performed every 12 months.
Q3: What causes small 4-cyl reciprocating compressor safety valve blockage?
A3: Oil sludge deposits stick the valve disc and block the valve.
Q4: What damages medium 4-cyl reciprocating compressor safety valve sealing seat?
A4: Repeated pressure shock impacts and damages valve sealing surface.
Q5: Where are safety valves installed on large 4-cyl reciprocating compressor system?
A5: Safety valves are fitted on cylinder head and interstage pipeline for dual protection.
Q6: What risk increases if safety valve annual calibration is omitted?
A6: Overpressure explosion risk rises by 48%.
Q7: How to arrange safety valve protection for single-unit two-stage refrigeration compressor?
A7: Separate safety valves are required for low-stage, high-stage and interstage pipeline.
09-25

2026

Reciprocating refrigeration compressor non-condensable gas accumulation detection and purge operation guide

Non-condensable gas mainly includes air, nitrogen and decomposition gas; it accumulates in condenser, raises condensing pressure and reduces refrigeration system efficiency.
When actual condensing pressure is higher than saturation pressure corresponding to cooling medium temperature by more than 0.07 MPa, non-condensable gas needs to be purged.
Xiteliduo reciprocating compressor system is equipped with automatic non-condensable gas detector; continuous pressure deviation over 0.05 MPa triggers automatic purge suggestion.
Small 4-cyl reciprocating refrigeration compressor system non-condensable gas mostly enters through shaft seal and valve packing during negative pressure operation.
Medium 4-cyl reciprocating refrigeration compressor non-condensable gas may be introduced after maintenance; air remains inside pipeline after assembly without vacuuming.
Large 4-cyl reciprocating refrigeration compressor system with multi-condenser layout has higher gas accumulation risk; non-condensable gas gathers at upper condenser chamber.
Large 6-cyl reciprocating refrigeration compressor running with high compression ratio may generate refrigerant decomposition gas; such gas also belongs to non-condensable component.
Many refrigeration teams perform blind purge without testing. Improper purge operation leads to refrigerant loss and increases operation cost by 34%.
Single-unit two-stage refrigeration compressor non-condensable gas mainly accumulates in high-stage condenser; low-stage negative pressure zone is the main gas ingress point.
Cascade unit high-stage reciprocating refrigeration compressor loop operates at higher pressure; non-condensable gas here will create more obvious condensing pressure rise.

### FAQ

Q1: What pressure deviation indicates non-condensable gas accumulation in reciprocating compressor system?
A1: When condensing pressure exceeds saturation pressure by more than 0.07 MPa.
Q2: What deviation threshold triggers Xiteliduo automatic purge recommendation?
A2: Sustained pressure deviation greater than 0.05 MPa.
Q3: Where does non-condensable gas enter small 4-cyl reciprocating compressor system?
A3: Air leaks in through shaft seal and packing under negative pressure condition.
Q4: What is the source of non-condensable gas after medium 4-cyl compressor overhaul?
A4: Air trapped inside pipelines due to incomplete vacuuming.
Q5: Where does non-condensable gas tend to gather in large 4-cyl multi-condenser system?
A5: It accumulates at the upper chamber of the condenser.
Q6: What economic loss will blind purge without gas detection cause?
A6: Refrigerant waste raises operating cost by 34%.
Q7: Where does non-condensable gas mainly accumulate for single-unit two-stage compressor?
A7: Non-condensable gas accumulates mainly inside high-stage condenser.
09-25

2026

Reciprocating refrigeration compressor shaft seal leakage diagnosis, replacement and oil retention control

Shaft seal isolates crankcase lubricant from atmosphere; shaft seal failure causes oil leakage or air ingress, which will contaminate lubricant and reduce vacuum performance.
Visible oil dripping exceeding 5 drops per minute is defined as severe shaft seal leakage; air ingress through damaged shaft seal will raise system non-condensable gas content rapidly.
Xiteliduo reciprocating compressor adopts spring-loaded mechanical shaft seal; shaft displacement exceeding 0.04 mm will accelerate seal face wear and trigger leakage.
Small 4-cyl reciprocating refrigeration compressor shaft seal damage often occurs after long standby; static seal face adhesion happens during shutdown period.
Medium 4-cyl reciprocating refrigeration compressor shaft seal leakage may be induced by crankcase pressure surge; frequent pressure shock damages seal contact surface.
Large 4-cyl reciprocating refrigeration compressor shaft seal cooling relies on circulating lubricant; oil supply interruption will cause seal face overheating and thermal cracking.
Large 6-cyl reciprocating refrigeration compressor crankshaft slight runout will concentrate friction on partial shaft seal surface; local wear gradually develops into leakage path.
Many maintenance operators only replace shaft seal when oil dripping appears. Early micro leakage without visible drops increases oil oxidation speed by 38%.
Single-unit two-stage refrigeration compressor low-stage shaft seal works under suction vacuum condition; damaged seal allows air to suck into refrigeration circuit.
Cascade unit high-stage reciprocating refrigeration compressor shaft seal bears high crankcase temperature; high temperature hardens sealing rubber and shortens service life.

### FAQ

Q1: What dripping rate is regarded as severe shaft seal leakage of reciprocating compressor?
A1: Oil dripping more than 5 drops per minute is severe shaft seal leakage.
Q2: What shaft displacement threshold will accelerate Xiteliduo mechanical shaft seal wear?
A2: Shaft displacement over 0.04 mm speeds up the wear of seal faces.
Q3: Why may small 4-cyl reciprocating compressor shaft seal fail after long shutdown?
A3: Static adhesion occurs between sealing faces during standby time.
Q4: What factor may damage medium 4-cyl reciprocating compressor shaft seal contact surface?
A4: Repeated crankcase pressure surge and shock load.
Q5: What is the cooling medium for large 4-cyl reciprocating compressor shaft seal?
A5: Circulating lubricating oil provides cooling for shaft seal assembly.
Q6: What consequence will invisible micro shaft seal leakage bring?
A6: It accelerates lubricant oxidation by 38%.
Q7: What problem will damaged low-stage shaft seal cause for single-unit two-stage compressor?
A7: Air is sucked into the refrigeration system under suction vacuum.

‹
1
2
3
4
5
6
...
14
15
›

‹
1
2
3
4
5
6
...
10
11
›

‹
1
2
3
4
5
6
...
12
13
›

‹
1
2
3
4
5
6
7
8
›

全部新闻 +

Obtain product customization plans online

Please fill in the requirements in the box below, and you will be able to obtain it for free.

Consulting Hotline

+86-18157593311

Xiteliduo & Chuanli

China Source Factory of R32 Semi-Hermetic Piston Compressor & Custom Turnkey Industrial Refrigeration System. Self-developed compressor + complete refrigeration solution, stable performance for tropical & ultra-low temperature working conditions.

connect us

Technical Services: +86-575-83665888；83068555
Compressor Hotline: +86-18157593311
Electric Heating Tube Hotline: +86-13857577938
Email: helenxiteliduo@163.com
Electric Heating Tube Factory: No. 150, Donghu Village, Ganlin Town, Shengzhou City, Shaoxing City
Compressor Factory: No. 679, Dongguo Economic Development Zone, Shengzhou City, Shaoxing City

Call us : (+86) 181 5759 3311

News

NEWS CENTER

Reciprocating refrigeration compressor discharge temperature control, high temperature trip and root cause analysis

Reciprocating refrigeration compressor motor starter, contactor inspection and overload protection setting principle

Reciprocating refrigeration compressor refrigerant charge amount calculation, overcharge / undercharge fault characteristics

Reciprocating refrigeration compressor cylinder head, valve plate assembly disassembly sequence and reassembly torque standard

Reciprocating refrigeration compressor lubricating oil pump inspection, pressure regulation and internal leakage troubleshooting

Reciprocating refrigeration compressor coupling alignment, thermal offset compensation and coupling damage diagnosis

Reciprocating refrigeration compressor foundation design, anchor bolt inspection and anti-vibration pad replacement specification

Reciprocating refrigeration compressor shutdown storage, long-term idle preservation and restart pre-check procedure

Reciprocating refrigeration compressor energy efficiency test method, index calculation and energy saving potential assessment

Reciprocating refrigeration compressor safety valve type selection, periodic inspection and replacement criteria

Reciprocating refrigeration compressor non-condensable gas accumulation detection and purge operation guide

Reciprocating refrigeration compressor shaft seal leakage diagnosis, replacement and oil retention control

Electric Finned Heater SCR Power Regulation & Phase Angle Control

Finned Tubular Heater Thermal Shock Resistance & Cyclic Thermal Fatigue Test

Air Finned Tubular Heater Carbon Footprint & Low-Carbon Product Design

Finned Tubular Heater Project Acceptance Checklist & Site Handover Document

Fin Heating Tube Terminal Design, Crimping & Hermetic Sealing

Electric Finned Heater Hazardous Area ATEX / IECEx Explosion-Proof Design

Finned Tubular Heater Vibration Fatigue & Anti-Vibration Mounting Design

Air Finned Tubular Heater Waste Heat Recovery & Secondary Heat Utilization

Finned Tubular Heater BIM Model & Digital Twin for Industrial HVAC & Refrigeration

Fin Heating Tube Anti-Corrosion Passivation & Post-Treatment Inspection

Electric Finned Heater Control Cabinet Layout & Heat Dissipation

Air Finned Tubular Heater Altitude Derating & High Altitude Application

Refrigeration Compressor Liquid Line Components Design | Sight Glass, Solenoid Valve and Filter Drier Layout

Piston Refrigeration Compressor Cylinder Liner Inspection and Replacement | Internal Clearance Control

Refrigeration Compressor Vibration Monitoring and Spectrum Analysis | Early Detection of Mechanical Defects

Refrigeration Compressor Warranty Management | Commissioning Record and Maintenance Compliance

Refrigeration Compressor Pipe Expansion Joint and Flexible Connection | Isolate Vibration Transmission

Refrigeration Compressor Oil Analysis and Trend Monitoring | Predictive Maintenance Tool

Refrigeration Compressor Ambient Temperature Control | Compressor Room Ventilation Design

Piston Refrigeration Compressor Crankshaft Inspection and Wear Judgment | Overhaul Critical Measurement

Refrigeration Compressor Expansion Valve Matching and Commissioning | Suction Superheat Stabilization

Semi-Hermetic Refrigeration Compressor Internal Thermal Protection Principle | Winding Overheat Protection

Refrigeration Compressor Filter Drier Selection and Replacement Cycle | Remove Moisture and Acid

Piston Refrigeration Compressor Multi-Compressor Rack Synchronization Control | Load Balance and Anti-surge

Q: Do you support OEM & ODM service for compressors?

Q: Is the sample quality the same as bulk production?

Q: How long for sample delivery? Who bears the sample freight cost?

Q: Can I get samples of the refrigeration compressor?

Q: What about temperature resistance, corrosion resistance and service life?

Q: Where can this refrigeration compressor be applied?

Q: What models and specifications are available?

Q: What material is the refrigeration compressor made of?

Q: Can I visit your factory?

Q: What is your annual production capacity?

Q: What certifications do you have?

Are you a factory or trading company?